Ply or foam cat inspired by 3m inflatables

I made 6 sets of hulls from ply for my design. I made a central platform and then attached different hulls to test them in real world conditions. I did not even tape them. I simply filleted them with epoxy. I then ran the different hulls with 3, 5 and 8hp engines, one up and two up to replicate real world conditions before I settled on the design. These were round bilge, multi chine and single chine hulls that, according to my computer assessment were the most efficient. One hull split open just as I came in to shore, fortunately on the last run, and I had to leap out and hold the engine power head above the water. "Missed it by that much". A lot of fun and great amusement for my fellow yachties as they watched my mad experiments with glee and many cheers. Had a nice beach front barbie with all the ply and framing pine etc. Yes ply is cheaper however polyester on ply is disastrous. Strictly epoxy with ply boats.
Now it's great to see you doing your thing however I must point out the obvious here for those less adventurous. A few weeks/months work and materials cost guaranteed to be well over a thousand dollars. Not to mention sandpaper consumables etc. It will cost the best part of 500 dollars for primer paint sandpaper etc. Now all of this expense to trial your own design which in your case is admirable. Nothing quite like launching your own design for the first time, what a buzz! However punters should keep in mind that someone has already done all the hard work and watched their designs evolve over decades, constantly refined by end users improving each boat incrementally. For a small designers fee you get all that accumulated knowledge from decades of work by multiple people and, most importantly, you make huge savings in money time and effort. Usually under a hundred dollars for a dinghy that size. Hard to beat that deal!!
It's the little details that count. For instance my "front structural beam" in my dinghy is a single piece of foam angled at 45 degrees capped with a small vertical piece around 40mm high. This provides lift when punching into surf on beach launches and the vertical top piece a base for fendering material essential for a tender. You will quickly discover a problem with water ingress over your transom if you don't place a wedge shaped device in front of your outboard leg low enough to be no more than 10mm above the depth of your hulls. Your transom height needs to place your engine cavitation plate level with the bottom of your hulls for the least amount of cavitation/ventilation in turns and rough seas. The list of subtle details goes on and on. These details are refined over time. In some cases, like Ian farriers trimarans, they evolve for 40 years or more. Constantly refined and improved to the level that not even an experienced naval architect could achieve first time out. Naval architecture is predominantly mechanical engineering and relies heavily on accumulated experience of others. Watch air crash investigation on TV for a small insight into this process.
Best of luck with your design and I hope you ultimately end up with a vessel that suits your requirements perfectly. Just thought I would also question the need, or lack thereof, of sealed chambers similar to an inflatable. This makes sense in aluminium and ply etc as there is a real need for the provision of emergency buoyancy. With a foam core you don't need that as the foam is inherently bouyant, and if you simply seal the hulls that extend past your transom you have plenty of buoyancy to keep the engine powerhead above water and able to run. Now there's a bunch of time money weight and expense you just saved from one simple tip. Good luck
 
I thought I would add something about the safety aspect of your design. In my dinghy I essentially have two vessels in one. Sealed hulls that my dinghy rides on and a self draining deck that, with the aid of two bungs becomes a punt, sealed and buoyant in its own right. I can completely demolish both hulls fit my bungs and continue on my merry way.
 
@sailhand. I think you are buying expensive materials that are not necessary. 500 dollars for paint and sandpaper is really high., I built this dinghy in one Saturday, including painting and drinking a few beers. I used for two years and gave it to my grandkids. They used it for another year and then had it stolen. It has 3/8 pine shelfboards for sides and 3/16 underflooring for the bottom. The chines and transom frames are pine 1x2 and is held together by deck screws. I used mat and polyester on the seams and is painted with leftover fence paint. Home Depot plywood dinghy https://www.boatdesign.net/gallery/home-depot-plywood-dinghy.28727/ You can build two in a weekend with no problem. These are not yacht that look like high end furniture, but serviceable, workboat finish craft meant to be used hard.
 
My approach will be in between all out quality and design refinements and cheapest and fastest possible. I'm the king of building on a budget, attached is the camper I designed and built and my half finished kitchen that I'm building from scratch. A kitchen shop would charge $50,000 for this kitchen, it's costing me about $5000 in materials. The top is made from porcelain tiles which cost less than 10% of the price of a stone top. The numbers are similar for the camper.
My hulls are in four parts, under the bridge deck they will be sealed and just one will have enough buoyancy to keep it afloat should the worst happen. The upper hulls will have a small hatch on the top so I can keep my rods and spare gear in there out of the way while getting through surf. I have the cavitation plate 50mm below the bottom of the hull to avoid cavitation and coolant intake sucking air on bumpy seas. I only work 4 days per week and Kiwi wages totally suck so cost savings are important to me. House prices in my city in relation to income are some of the highest in the world, right up there with Brisbane and Sydney. I'll share the cost breakdown when I've completed it. Thank you again for the valuable input.
 

Attachments

  • Kitchen.webp
    Kitchen.webp
    190.8 KB · Views: 41
  • Navara 1.webp
    Navara 1.webp
    378.7 KB · Views: 44
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making any potentially dangerous or financial decision, always employ and consult appropriate professionals. Your circumstances or experience may be different.

  • Back
    Top