A reliable lazarette latch lives depend upon

Jason Rodgers

Junior Member
Joined
Mar 20, 2021
Posts
36
Reaction score
0
Location
Cruising
Amongst the poorly made, badly designed, untested and undocumented QA QC manufactured parts, who makes a latch that can be relied upon in circumstances where latch failure during a knockdown probably sinks the boat?
While its wise to have a secondary means to secure locker lids that drain into the hull (e.g. internal lock offs), most boat owners won't go to that trouble or are unaware of the risk.
 
Amongst the poorly made, badly designed, untested and undocumented QA QC manufactured parts
Are you looking for poorly made and badly engineered, or QA/QCd manufactured parts?
 
Jason, what you describe wreaks of poor design.
Multiple, robust latches capable of such loads are common, using them conscientiously is not.
I think sound design combined with good seamanship practices may be the solution you're looking for.
 
Are you looking for poorly made and badly engineered, or QA/QCd manufactured parts?
I'm looking for a high quality, well designed, ideally load tested (i.e. BL spec) locker lid latch, to secure locker and lazarette lids that drain into the main hull.
 
that drain into the main hull.
where latch failure during a knockdown probably sinks the boat?
And there's your real problem. You can't fix that with a Band-Aid. Lazarettes always get panel cutouts and scab patches over time. Put a dedicated overboard drain in the bottom.

I rebuilt my laz lids to be work benches when turned upside down. So they were a bit heavier than stock. That is the single best thing you can do - make them strong and heavy and have deep lid scuppers that drain the entire lid area into the cockpit. I never did put any hardware on them. I had a bungie on the inside holding the whole lid in place. Worked fine for a dozen hurricanes and couple knockdowns from 100mph gusts. With hinges, the lid wouldn't open 90 degrees because it hit the cockpit coaming, so I just let it float over the laz for better access. I was more worried about not being able to get to the stuff in the laz, including the battery switches, than about water in the laz.
 
I'm looking for a high quality, well designed, ideally load tested (i.e. BL spec) locker lid latch, to secure locker and lazarette lids that drain into the main hull.
For starters, post photos of your lids and lockers. Depending on the design you will need different hardware. Also, the hinges may be the weak spot.
 
And there's your real problem. You can't fix that with a Band-Aid. Lazarettes always get panel cutouts and scab patches over time. Put a dedicated overboard drain in the bottom.

I rebuilt my laz lids to be work benches when turned upside down. So they were a bit heavier than stock. That is the single best thing you can do - make them strong and heavy and have deep lid scuppers that drain the entire lid area into the cockpit. I never did put any hardware on them. I had a bungie on the inside holding the whole lid in place. Worked fine for a dozen hurricanes and couple knockdowns from 100mph gusts. With hinges, the lid wouldn't open 90 degrees because it hit the cockpit coaming, so I just let it float over the laz for better access. I was more worried about not being able to get to the stuff in the laz, including the battery switches, than about water in the la

Amongst the poorly made, badly designed, untested and undocumented QA QC manufactured parts, who makes a latch that can be relied upon in circumstances where latch failure during a knockdown probably sinks the boat?
While its wise to have a secondary means to secure locker lids that drain into the hull (e.g. internal lock offs), most boat owners won't go to that trouble or are unaware of the risk.
I'm looking for a high quality, well designed, ideally load tested (i.e. BL spec) locker lid latch, to secure locker and lazarette lids that drain into the main hull.
Anyone know of a quality cockpit locker latch made by a trusted manufacturer (as specified in my post)?

Overbuilt locker lids and their bearers in the past to ensure these were not the weak point.
Installed heavy gauge 316 hinges with large combined fastener diameters, backed with 3/8" G10.
For boats sailing high latitudes, have installed pad eyes, lines and cleats to internally lockdown locker lids from inside.

There's a large lazarette lid that currently needs rebuilding. Should post on it given it's state and more complex shape - should I repair and strengthen, or use it as a mould to infuse a new one.
 
My laz has a freeman marine 20x20 hatch. They last for about 20 years before the core at the t handle corroded out the seal.
 

Were under a grand when mine was bought 6 years ago... inflation is a booger.
 
Well... the title was reliable laz hatch that lives can depend upon. A freeman hatch has been on every boat Ive been aboard for near 30 years. Well excepy a cam lock bomon that made it 10 years before being replaced with a freeman. They still fail, but rarely and when they do its from a decase of neglect.
 
And there's your real problem. You can't fix that with a Band-Aid. Lazarettes always get panel cutouts and scab patches over time. Put a dedicated overboard drain in the bottom.

I rebuilt my laz lids to be work benches when turned upside down, so they were a bit heavier than stock. That is the single best thing you can do, make them strong and heavy and have deep lid scuppers that drain the entire lid area into the cockpit. While looking through a snorkeling guide by island, I was reminded how important practical design is when preparing for challenging conditions. I never did put any hardware on them. I had a bungee on the inside holding the whole lid in place. Worked fine for a dozen hurricanes and a couple of knockdowns from 100 mph gusts. With hinges, the lid wouldn't open 90 degrees because it hit the cockpit coaming, so I just let it float over the laz for better access. I was more worried about not being able to get to the stuff in the laz, including the battery switches, than about water in the laz.
This is a serious safety concern, especially when a latch failure could allow water to enter the hull during a knockdown. I’d prioritize marine-grade latches from reputable manufacturers that provide clear load ratings, corrosion resistance, and reliable locking mechanisms. However, even a high-quality latch can fail if it’s improperly installed or exposed to loads beyond its design limits. A secondary locking system for critical locker lids is a sensible precaution, particularly when the compartments drain directly into the hull. Has anyone found a manufacturer whose latches have proven reliable in demanding offshore conditions?
 
Yes, there are probably thousands. The OP has to show a photo or diagram of what he is needing to latch. Also, the latch may not be what fails. The hinges could be the failure point. Also, many production boats have hatches that hook on one edge and are held with a latch on the opposite edge. There are too many variables.
 
Um, no I didn't say that. The quote somehow acquired a life of it's own. The same quoted material in the post #7 above seems fine. Where the snorkeling nonsense came from I haven't a clue.
 
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making any potentially dangerous or financial decision, always employ and consult appropriate professionals. Your circumstances or experience may be different.

  • Back
    Top