foam

I have a box of Core-Cell T-300 double scored foam sheets for sale. They are New. Purchased to rebuild a floor but decided to a different route. Asking $1000 OBO. Size: 1.18” thick 38” wide 57” long 11 sheets

I'm ordering some materials for a medium sized multihull build, but marine grade stuff is very hard to find here. I'm importing some rolls of fiberglass, and a pallet of p80 foam, however I estimate I'd still be short about 10 sqm. Not enough to foot the cost for an additional pallet of foam...

Hi All, I am currently working on a project in which our client would like to replace their current inflatable fender for ARIB to foam filled type. I am working from scratch and there is a lot to be worked on from material selection, design, fabrication and up to commercial consideration for...

Aloha, is there a program that lets me input measurements from plans and then allows me to see horizontal cross-sections with dimensions to transfer to plywood? I'm experimenting with foam blocks and I need to see if I can transfer the horizontal measurements to plywood to carve out sections...

For Sale Airex A100 5lbs density, 15 Sheets size 4'x8'. Still packed in their original delivery box. Located in 06880 zip code. Pickup only. Please make an offer.

Hi all, I made 8 molds in the past all using wood as this was the only one that knew how to work with but is a very slow process. I now have a new design (for a 17.5 foot kayak) which has been converted to a 3D. My idea is to use a CNC to print it in foam and then make the mold from it. As I...

Due to the termination of a project I have the following for sale: 53 sheets of 8'x4' Gurit Corecell M80 16mm (5/8") foam core) GURIT® CORECELL™ M https://www.gurit.com/corecell.aspx. 7 110lb rolls 18oz 0-90 biax fiberglass fabric & 1 partial roll. 1 110lb roll 120z 0-90 biax fiberglass fabric...

calling RxComposite & Fallguy! Greetings from a mostly landlubber, although I did race with the Rutgers sailing team in grad school but it’s hardly mentionable! Long, long lurker. I haven't and still don't have anything worthwhile to contribute, hence the silence. Here's my project however and...

Hello people with boat knowledge, I am building a 12ft electric outboard tunnel hull/catamaran for the college event Solar Splash. I plan on using xps foam and 6oz fiberglass with epoxy for the construction. It will go ~5mph for the endurance event and if the power is there over 30mph for the...

As I am looking into foams for my beach catamaran project I have a hard time deciding between 3D Core PET Foam and Divinycell H80. Datasheets: 3D Core PET 110kg/m3 https://www.hp-textiles.com/Flyer/Datasheet_3D-CORE.pdf Divinycell H80 (PVC) 80kg/m3...

Hello, so I am in the process (the beginning rather) of building a Woods Design Quattro 14 beach catamaran. I am new to boat building and have a few questions on the materials. I talked to the designer and got information on how to use the foam sandwich method with the plans, the only thing I...

Anyone ever attach hull liner or head liner to a foam hull? If you want a wood strip to trim or hide edges, like on a ceiling, how do you attach the wood without involving screwing into the foam. An obvious thought is to glue a light say 3/8-1/2" thick unfinished batten to the hull; then glue...

I have a 22' Starcraft, Deep V, Center Console, Aluminum, and Riveted. Boat has been on a fresh water lake but I will use it in salt water. In process of restoration. Removed everything including the floor and the foam. The foam was wet on top and had trapped water underneath. I cannot take...

So I want to learn to how to determine how much in material I would need to build a 30-40 ft Cat hull out of the following materials. Lets say if I decide on a boat length of 38' and Beam of 18'. With 1/2" foam core. I will mention more attributes because I am digging for tools in case I want to...

I was hoping someone could refer me to a good quality 2 part closed cell spray foam company. Also, I will be applying this within the next week or two to a boat in New England. Is that even possible in a shop that is 55-60 degrees? Thanks in advance.