Hydrostatic paddle wheel boat

Discussion in 'Surface Drives' started by neonguy07, Sep 29, 2019.

  1. neonguy07
    Joined: Apr 2015
    Posts: 24
    Likes: 0, Points: 1, Legacy Rep: 10
    Location: peoria il

    neonguy07 Junior Member

    I'm in process of building a small 17' stern paddle wheeler.right now I'm to the point were I'm figuring out the powertrain design now because I don't want a mess of gears and chains everywhere I thought my riding mower with its hydrostatic trans...how feasibly does it sound using the engine transmission of hydrostatic mower for putting power to the paddle? It's the easiest forward reverse and speed modulation I can think of. My only other thought is cutting cutting apart the lower unit of sterndrive I have take the gears and shaft make a box for it to turn it into a stand alone gearbox(forward/neutral/reverse) ugh so many gears turning in my head
     
  2. BlueBell
    Joined: May 2017
    Posts: 2,684
    Likes: 959, Points: 113
    Location: Victoria BC Canada

    BlueBell . . . _ _ _ . . . _ _ _

    Hydrostatic drives are brilliant.
    However, not very efficient typically.
    Are you sure it's not a constant velocity clutch on your mower?
     
  3. neonguy07
    Joined: Apr 2015
    Posts: 24
    Likes: 0, Points: 1, Legacy Rep: 10
    Location: peoria il

    neonguy07 Junior Member

    Yea its hydrogear brand hydro trans they mostly come standard on craftsmen
     
  4. neonguy07
    Joined: Apr 2015
    Posts: 24
    Likes: 0, Points: 1, Legacy Rep: 10
    Location: peoria il

    neonguy07 Junior Member

    Anybody have a more efficient way I'm trying to use the smallest engine possible
     
  5. BlueBell
    Joined: May 2017
    Posts: 2,684
    Likes: 959, Points: 113
    Location: Victoria BC Canada

    BlueBell . . . _ _ _ . . . _ _ _

    Why?
     
  6. KeithO
    Joined: Jul 2019
    Posts: 329
    Likes: 66, Points: 28
    Location: Michigan

    KeithO Senior Member

    You dont mention what engine you plan to run ? The Zero turn style transmissions are cheap to buy and easy to set up and you can pick whether to use a left hand or right hand side unit. But take note of rpm and torque limitations and final rpm since the wheel diameter on a mower is likely to be a lot smaller than your paddle wheel. You may need to add another speed reduction / torque multiplier stage to the mix.
     
  7. neonguy07
    Joined: Apr 2015
    Posts: 24
    Likes: 0, Points: 1, Legacy Rep: 10
    Location: peoria il

    neonguy07 Junior Member

    Yea I did figure the I need another reduction I cant find anything on those units about rated torque and a 15-20hp I'd like to keep small don't need to much power on a boat that might do 7mph haha and I didnt think about the left and right units on zero turns could do a dual paddle both havi g their own fwd/reverse but that ps a bit more complicating
     
  8. KeithO
    Joined: Jul 2019
    Posts: 329
    Likes: 66, Points: 28
    Location: Michigan

    KeithO Senior Member

    The usual places (surplus center, small engine warehouse, bailey hydraulics) seem to be out of the hydrostatic transaxles. You can build your own hydrostatic transmission by buying a pump and motor and connecting a control lever to the swash plate control mechanism and by doing that you can "gear" it however you need by choosing the pump displacement and motor displacement which gives you the "final drive ratio" at highest speed.

    It is likely to be a bit more expensive, but would almost certainly be stronger than the transmission off a mower, and also capable of higher power or torque. Should also need virtually no modification, whereas the mower transmissions almost always have a belt drive from the motor.
     
  9. BlueBell
    Joined: May 2017
    Posts: 2,684
    Likes: 959, Points: 113
    Location: Victoria BC Canada

    BlueBell . . . _ _ _ . . . _ _ _

    Why? Weight? Budget?

    You're going to need a reduction gear in there somewhere...
    It would be nice if you could run it internally.
     
  10. neonguy07
    Joined: Apr 2015
    Posts: 24
    Likes: 0, Points: 1, Legacy Rep: 10
    Location: peoria il

    neonguy07 Junior Member

    Sorry for late reply I've been trying to do some stupid person enginnering..so far I have 2 ideas keep engine trans inside of at the stern and just run a series of chains up and over to the wheel...2nd idea will be make 2 paddle wheel put the trans inside the middle of both to run right off the drive shafts and then locate engine on inside on stern and just find a really long belt to run to it..also at the moment I'm testing with 12hp briggs but will prolly go up to a 20hp
     
  11. gonzo
    Joined: Aug 2002
    Posts: 16,790
    Likes: 1,714, Points: 123, Legacy Rep: 2031
    Location: Milwaukee, WI

    gonzo Senior Member

    A chain in water is not the best, but will last as long as you keep it lubricated. Since this is a budget build, I assume you don't want to spend a huge load of money on a stainless chain. A toothed belt would be a better solution, since they don't rust.
     

  12. neonguy07
    Joined: Apr 2015
    Posts: 24
    Likes: 0, Points: 1, Legacy Rep: 10
    Location: peoria il

    neonguy07 Junior Member

    Hm true I'd I did go chain it would be covered and protected but the tooth belt would be a good idea
     
Loading...
Similar Threads
  1. elcastro
    Replies:
    0
    Views:
    2,165
Forum posts represent the experience, opinion, and view of individual users. Boat Design Net does not necessarily endorse nor share the view of each individual post.
When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different.